Low-Iron Glazing by Application

Ultra Clear Tempered Glass – Low-Iron Application

Low-Iron Glazing by Application

Glazing decisions are made per job, not per catalogue page — a shopfront, a shower screen and a balustrade all ask the glass for the same things: no colour cast, no distortion and a break pattern that is safe. That is why ultra clear tempered glass turns up again and again across fit-outs. This guide takes the material application by application: the thickness worth discussing, the edge finish that stays visible, the fixing detail that decides the order, and where low iron tempered glass earns its premium over standard clear.

Ultra clear low iron tempered glass
4–19 mmTempered thickness range
Up to 91%+Light transmission
Up to 5×Stronger than regular glass
3660 × 2440 mmLargest sheet size

Four numbers set the envelope. Everything below is about how those numbers are used once the sheet leaves the rack and lands on a specific job.

Start with the job

Pick your application, then read the spec

Six job types cover almost every enquiry this sheet receives. Each block below carries the same five fields, so two applications can be compared line for line.

The five fields that decide the order

Specifications, application by application

Thickness is only the first question. Edge finish, the fixing detail and the fabrication sequence decide whether the panel works on site or comes back.

Application 01

Retail shopfronts & showcases

The job here is colour fidelity. The glass exists to be looked through, not looked at, and a green cast quietly changes the colour of everything behind it.

Thickness to discuss
8–12 mm for full-height glazed fronts; 6 mm and upward for framed display cases. Final thickness follows panel size and wind load.
Edge finish
Flat edge where the edge sits inside a frame; polished where a frameless showcase leaves the edge on show.
Fixing note
Framed storefront systems and point-fixed details both need the hardware layout settled before the panels are tempered.
Compliance
Certified safety glazing — the four standards referenced in the specification table apply here as everywhere on this page.
Common failure mode
Standard clear glass greening the edge and face, so the merchandise on display reads a shade off against the reference sample.

Application 02

Frameless shower enclosures

Every edge is exposed and every edge is handled daily, so the finish is not a detail — on a frameless screen, the edge is the product.

Thickness to discuss
8–10 mm for fixed side panels, hinged doors and walk-in screens.
Edge finish
Polished, and optionally beveled — both are commonly recommended on edges that stay visible after installation.
Fixing note
Hinges, clamps and handles need drilled holes and cut-outs. All cutting, drilling and edge work is completed before tempering.
Compliance
Certified safety glazing, with the blunt break pattern that safety glazing requirements are written around.
Common failure mode
Hardware ordered against an unpolished edge, or hole positions requested after the panels have been tempered.

Application 03

Facades, canopies & entrances

Large panels, real wind load, and a colour cast that shows up most clearly against the sky — the one place where a slight green tint is hardest to hide.

Thickness to discuss
10 mm and up for large entrance leaves and canopy panels, heavier where the span and fixing detail call for it.
Edge finish
Flat or seamed behind framing; polished on exposed canopy and entrance edges.
Fixing note
Point-fixed and framed systems both put the panel weight onto the structure — agree support and lifting before the panel size is frozen.
Compliance
Certified safety glazing, with submittal data available for the project file.
Common failure mode
Panel weight and support underestimated at design stage and discovered on the day of installation.

Application 04

Railings & balustrades

A safety element read at close range. The top edge and the corner details are what a client notices first, long before they notice the panel itself.

Thickness to discuss
10–15 mm for balustrade infill and stair panels, with the panel height and fixing type set before ordering.
Edge finish
Polished, particularly on top edges and corners that sit at hand height.
Fixing note
Base-shoe and clamped systems need fixing holes set out before tempering; keep each panel inside the 3660 × 2440 mm maximum sheet.
Compliance
Certified safety glazing — confirm which standard your project is inspected against before the order is placed.
Common failure mode
Mixing thicknesses across one run, so panel weights and finished heights no longer line up.

Application 05

Furniture & table tops

The thickest polished edges on this page — and the place where a green cast is most obvious, because the edge is right in front of the user.

Thickness to discuss
10–19 mm; 12 mm for most dining and console tops, 19 mm for large counters and heavy-duty surfaces.
Edge finish
Polished or beveled. On a table top the edge is a design feature, not a hidden detail.
Fixing note
Stand-offs, frames and bonded fixings all need the layout agreed on the fabrication drawing before production.
Compliance
Certified safety glazing, with the blunt break pattern that matters on a surface people lean on.
Common failure mode
A tinted edge on a 19 mm top — precisely where low-iron shows its value and standard clear shows its colour.

Application 06

Interior partitions & doors

Volume work: many similar panels, where consistency from one sheet to the next matters more than the performance of any single piece.

Thickness to discuss
8–12 mm for partition panels and frameless door leaves.
Edge finish
Flat inside frames; polished on frameless doors and exposed returns.
Fixing note
Patch fittings, floor springs and locks need holes and notches cut before tempering — the hardware schedule drives the drawing.
Compliance
Certified safety glazing across the whole run, not just the first sample panel.
Common failure mode
Repeat orders placed without the original fabrication drawings, so new panels no longer match the installed hardware.

Work backwards from the thickness

Thickness × application cross-matrix

If you already know the thickness you want, use this view instead of the blocks above. It sorts the same six applications by dimension rather than by job.

ThicknessShopfrontsShowersFacadesRailingsFurniturePartitions
4 mm————○○
6 mm○○——✓✓
8 mm✓✓○○✓✓
10 mm✓✓✓✓✓✓
12 mm✓✓✓✓✓○
15 mm○○✓✓✓○
19 mm○—○✓✓○
✓ Recommended starting point○ Possible with caveats— Not advised

Treat this as the opening position for a quotation, not as final sizing. Thickness is settled by panel size, span, wind or impact load and the code your project is inspected against, and it is confirmed with the factory before the sheet is tempered. Weight follows thickness — roughly 2.5 kg per square metre for every millimetre — so a 10 mm panel runs about 25 kg/m², which makes support and lifting part of the specification rather than an afterthought.

Ultra clear low iron tempered glass sheet, product detail

The sheet behind all six applications

One product, six ways of using it

Every block above is cut from the same material. It is produced with a reduced iron content, which removes most of the greenish tint of standard glass and gives much higher optical clarity, with light transmission typically up to 91% or more. Colours behind the pane stay accurate and distortion stays minimal — the two reasons it gets chosen for displays, for exposed shower panels and for thick furniture edges.

It is tempered, so it resists thermal stress and mechanical impact and breaks into small blunt pieces rather than shards. It is also easy to maintain: the smooth surface cleans down quickly and resists grime build-up, which matters on high-touch doors and screens.

Product No.LYD-CLITG
MaterialUltra-clear low iron tempered glass
Thickness4 mm – 19 mm
Edge processingFlat edge and polished edge; seamed, round, flat or polished edges produced to drawings
StandardsCE EN 12150-2:2004 · ANSI Z97.1-2015(R2020) · CAN/CGSB-12.1-2022 · CPSC 16 CFR 1201-2024
Tempered colour rangeClear, ultra-clear low-iron, green, bronze / brown
PackingPlywood crates, A-steel racks and similar export packing
Port of loadingXingang port

Fabrication

Edge finish decides how much the glass is seen

On tint-free glass the edge reads almost as clearly as the face, so edge work is an appearance decision as much as a finishing one. All four profiles below are cut to the project drawing, and polished or beveled edges are commonly recommended wherever the edge stays exposed after installation.

Flat edge

Machine-ground straight edge for panels that sit inside a frame or beneath a shoe.

Polished edge

Clear, bright finish for frameless screens, doors and balustrades where the edge is handled.

Beveled edge

A sloped decorative profile, commonly specified on table tops and interior door leaves.

Seamed & round edge

Softened arris or radiused profile that takes the sharpness off edges handled in service.

Custom sizes and shapes are cut to drawings, with a minimum fabricated piece of 100 × 100 mm — small enough for bespoke inserts, shelf sets and signage panels.

Edge work and custom fabrication on ultra clear low iron tempered glass

Safety and submittals

What the tempering actually gives you

Clarity sells the sheet; the safety behaviour is what allows it into the building in the first place. Four things are worth knowing before you write it into a specification.

Strength after tempering

The sheet is heat-treated to raise its resistance to thermal stress and mechanical impact, and tempered glass is up to five times stronger than regular glass of the same thickness.

Break behaviour

When it does break, it shatters into small blunt pieces instead of large shards, which is the property safety glazing requirements around the world are written around.

Compliance and submittals

Four glazing safety standards are referenced in the specification table above. Check which one your project is inspected against, and request the matching documentation with the quote.

Weight and support

The material is heavy at the top of the range. Panel weight, substrate and lifting method belong in the same conversation as thickness, especially on facades and 19 mm tops.

Scenario to specification

Five situations, five straight answers

Most enquiries fall into one of these patterns. Match yours, then confirm the detail with the factory before the drawing is signed off.

If this is your job

The display colour has to be exact

Specify ultra-clear low iron glass at 8–12 mm with polished edges. Face and edge stay neutral, so the product behind the pane keeps the colour the brand approved.

If this is your job

Tint genuinely does not matter

Standard clear tempered glass does the same safety job for less. Where nobody will notice the tint, spend the difference on the edge work and the hardware instead.

If this is your job

A wet area with constant handling

Go for 8–10 mm with polished edges, and put every hinge, clamp and handle hole on the drawing before tempering. There is no drilling afterwards.

If this is your job

One very large single pane

Check it against the 3660 × 2440 mm maximum first. Oversize usually resolves into two panes with a mullion or a polished joint rather than a special order.

If this is your job

A handful of small bespoke pieces

Fabrication goes down to 100 × 100 mm, so small inserts, shelf sets and signage panels are viable — but they still need a dimensioned drawing, not a list of sizes.

If this is your job

A multi-storey interior fit-out

Keep one thickness and one edge spec across the run. Consistency between panels matters more than shaving a millimetre off any one of them.

Send the sheet, not a wish list

A factory quote comes back accurate when the enquiry already answers the questions production will ask. Send these and the reply is a price, not another round of emails.

  • Panel sizes or a dimensioned drawing, including any holes and cut-outs
  • Thickness per application, and the edge profile for each panel
  • Quantity, destination and required delivery window
  • Packing preference — plywood crates or A-steel rack
  • The safety standard your project is inspected against

The factory works through panel size, weight and fixing with you, then quotes with export packing included, loading from Xingang port.

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

Low Iron vs. Clear Float Glass in Architectural Glazing and Facades

Low iron and clear float glass can look nearly identical in a sample box, yet thickness, daylight, and layered views pull them apart.

Read article

Low Iron Tempered Glass for Shopfronts and Retail Displays

Low iron tempered glass earns its place in shopfronts and showcases by keeping merchandise color honest and by breaking into safer pieces when something goes wrong.

Read article

Choosing Low Iron Glass for Frameless Shower Door Systems

Frameless shower doors succeed or fail on the glass itself, so clarity, thickness, and factory-cut hardware holes matter far more than most buyers expect at first glance.

Read article

Frequently Asked Questions

what thickness range is available?

4 mm to 19 mm in the tempered range.

which thickness works for shopfronts and showers?

8 mm and 10 mm are marked suitable for shopfronts and showers; 10 mm is marked suitable across every application on the matrix.

what is the product number?

LYD-CLITG.

what material is it?

Ultra-clear low-iron tempered glass.

does the edge finish matter?

Yes — the edge finish decides how much the glass edge is seen, so specify polished or bevelled edges for the application.

what should I send for a quotation?

Thickness, application, panel sizes, edge finish and quantity.

Leave a message
Nome di battesimo *
E-mail *
Messaggio di WhatsApp *
Messaggio *
Noi usiamo Biscotto per migliorare la tua esperienza online. Continuando a navigare su questo sito web, diamo per scontato che tu accetti il nostro utilizzo di Biscotto .